Nissan Juke (2010-2019): How to Reset the Service Light

After completing an oil change or routine maintenance on your Nissan Juke, you might notice that the wrench-shaped service light on the dashboard remains illuminated when you start the car. This indicator reminds you that the car has reached its scheduled service interval. To reset it, you’ll need to follow a specific sequence using the dashboard buttons.

In this article, we’ll show you an easy, clearly structured method to reset the service light on any Nissan Juke model from 2010 to 2019 — no special tools required.

2. Why Does the Service Light Appear?

2.1 Purpose of the Indicator

The service reminder appears once the Juke reaches a preset mileage or time interval between services. It helps keep track of oil changes and maintenance schedules.

Nissan Juke Dimensions and Boot Space: Complete Guide to Size, Interior Room, and Hybrid Specs

2.2 What Happens If You Ignore It

Even though the car can still run normally, ignoring the reminder can lead to confusion about the next service interval. The light doesn’t indicate a malfunction — it’s simply a maintenance tracker, not the check-engine warning.

3. Applicable Models and Years

This procedure applies to Nissan Juke vehicles produced between 2010 and 2019, which display a wrench icon or “spanner” as the maintenance indicator.
Models from 2020 onward may require a different procedure since their dashboards and software are updated.

4. Preparation Before Resetting

4.1 Check These First

• Confirm that a full service has actually been completed (oil, filters, etc.).
• Ensure all doors are closed and the parking brake is applied.
• Make sure the engine is off, but the ignition is ready to turn on.

4.2 Locate the Button

You’ll use the trip or odo button located below the speedometer or on the dashboard. Some models have two buttons — you may need to use both simultaneously.

Nissan Juke Dimensions and Boot Space: Complete Guide to Size, Interior Room, and Hybrid Specs

Nissan Juke Dashboard Warning Lights: Complete Meaning & Symbols Guide (2010–2025)

5. Step-by-Step Reset Procedure

Step 1: Turn on the Ignition

1. Press the start button once (or turn the key) without starting the engine — just switch the ignition on.
2. Wait until all warning lights appear on the dashboard, especially the wrench icon.

Step 2: Press and Hold the Button

3. When you see the wrench symbol, press and hold the trip/odo button for about 3 seconds. The indicator or mileage display will start flashing.

Step 3: Adjust the Service Interval (if needed)

4. While the indicator flashes, press the button again to increase the service interval in 500 mile or 1000 km increments. If you don’t need to change it, just wait until the flashing stops.

Step 4: Finish and Confirm

5. Once the indicator stops flashing, release the button.
6. Turn off the ignition completely.
7. Start the car again to verify that the wrench icon has disappeared.

If the light remains on, repeat the process or check if another fault code is present.

6. Troubleshooting Common Issues

6.1 The Icon Does Not Disappear

• Ensure the driver’s door is fully closed — an open door can interrupt the reset sequence.
• Make sure you’re pressing the correct button or combination if your model has two.
• If the Check Engine or Service Engine Soon light is on, it may indicate an actual fault rather than just a maintenance reminder.

6.2 Push-Button Start Variations

Models with a push-button start (typically from 2015-2016 onward) might need a slightly different timing sequence — pressing the start button twice without the brake pedal may be required to enter ignition mode.

7. Final Notes

• This is a simple, cost-free procedure that ensures your maintenance record is accurate.
• Resetting the indicator does not replace actual maintenance; you must still change oil, filters, and inspect the vehicle regularly.
• Always note the date and mileage of each service for future reference.
• If the light doesn’t turn off after multiple attempts, a dealership or qualified technician can perform the reset with diagnostic equipment.

8. Conclusion

Resetting the service light on your Nissan Juke (2010-2019) is straightforward when done correctly: switch on the ignition without starting the engine, hold the button until the indicator flashes, wait, and then restart the car. Following these steps will keep your maintenance records accurate and your dashboard free of unnecessary warnings.

Nissan Juke Dimensions and Boot Space: Complete Guide to Size, Interior Room, and Hybrid Specs

Nissan Juke Dashboard Warning Lights: Complete Meaning & Symbols Guide (2010–2025)

Nissan Juke Tyre Size: The Complete 2025 Guide for Every Model and Trim

If you want to know other articles similar to Nissan Juke (2010-2019): How to Reset the Service Light you can visit the category Service and Parts.